Hot Water & Geothermal Pumps
Ganquan geothermal pumps extract water from hot-water wells for heating, hot spring facilities and greenhouse applications. Selection depends on water temperature, water chemistry, well conditions and the required flow and head.
Tell us about your well, water temperature and intended use. We can help review suitable pump options and coordinate the motor, materials and installation requirements for your project.

Built for hot water, not pulled off a shelf. Tell us your water temperature, the well’s dynamic level and the flow you need — we match the heat-resistant pump, cable and control gear to it.
Applications for Geothermal Pumps
Geothermal Heating
Extract hot water from geothermal wells to supply heat exchangers for building or district heating systems.
Hot Spring Facilities
Draw thermal water from wells for spa and bathing facilities, with pump selection matched to water temperature and chemistry.
Greenhouse Heating
Supply geothermal well water to heat exchangers for greenhouse heating, with flow matched to the project’s heating requirements.
QJR Hot Water Borehole Pumps
The QJR series is designed for extracting hot water from boreholes and geothermal wells. The appropriate model and motor configuration depend on the required flow, total head, water temperature, water chemistry and installation conditions.
| Parameter | Catalogue Range / Condition |
|---|---|
| Flow rate | 5–600 m³/h |
| Head | 6–600 m |
| Water temperature | Normally up to 100°C; higher temperatures require special technical review. |
These figures describe the overall catalogue range across different models. Maximum flow and maximum head do not apply simultaneously to a single pump. Temperature suitability must be confirmed for the complete pump and motor assembly. Final selection requires the proposed model’s performance curve and installation requirements.
Water Quality & Installation
Water temperature is only one part of selecting a geothermal well pump. Water chemistry and installation conditions also need to be reviewed. The following are selected water-quality limits listed in the QJR catalogue.
| Parameter | Catalogue Condition |
|---|---|
| pH value | 6.5–8.5 |
| Mineral content | No more than 4,000 mg/L |
| Solids content | No more than 0.01% by mass |
These are selected equipment operating conditions, not a complete water-quality specification or a drinking-water standard. Please share any available water analysis so the full catalogue requirements and suitability of the proposed materials can be checked.
Related Project Evidence
Installation Details to Confirm
- Borehole internal diameter, total depth and water level during pumping.
- Planned pump installation depth and submergence below the pumping water level.
- Required flow, total head and available power supply.
- Suitability of the motor and cable for the operating water temperature.
How your RFQ moves
- Tell us your water temperature, dynamic water level, required flow and head
- We select a candidate from the QJR hot-water series — the heat-resistant sibling of our QJ borehole family
- You receive a written quotation with model, parameters and lead time
- Production at our Tianjin facility
- Every pump is tested on our in-house test rig — rated parameters, leaks, reliable operation
- Shipment with packing list and documents
You know which step your order is at — no silent weeks.


Before you compare quotes, check these five lines
- Water temperature and required submergence — the manual ties them together: ≥40 m for 50–<80 °C, ≥50 m for 80–<100 °C, ≥70 m for 100–<120 °C water.
- Water chemistry — QJR accepts mineralization ≤4000 mg/L, chloride ≤600 mg/L, pH 6.5–8.5, no oil content.
- Duty point as flow and TDH together — maximum flow and maximum head never occur on a single pump.
- Heat-rated cable and control gear — the package is pump + heat-resistant cable + control panel + wellhead fittings, not just a pump.
- Custom supply and lead time — 380 V/50 Hz standard; 60 Hz, 220 V and 660 V are custom builds confirmed per order.
A cheaper quote that skips these lines usually costs more later.
Frequently Asked Questions
Our geothermal water is 95 °C. Can we use your pump?
Yes — QJR standard builds are rated up to 100 °C. For water at 80–<100 °C the unit must sit at least 50 m below the dynamic water level. Send us your dynamic level and required flow and we will check the fit.
What if the water is above 100 °C?
That is a special build — the group catalogue shows versions up to 120 °C with stainless or tin-bronze housings, requiring at least 70 m submergence. We confirm the exact configuration with the factory before quoting.
Can you build for 60 Hz or 220 V?
Yes — 60 Hz, 220 V and 660 V are listed customization options. Price and lead time are confirmed per order.
Read the guide: How to Select a Hot Water Borehole Pump for a Geothermal Well — the temperature vs submergence table, water chemistry limits and a worked example.
Tell Us About Your Geothermal Project
Tell us your project location, intended use and any well information you already have. Include the water temperature and required flow if known. We can help review suitable QJR pump options and identify the details needed for a quotation.
You do not need every technical detail to get started. Share any available well reports, water analysis or photographs of your existing pump and nameplate.
