Borehole Pumps for Irrigation & Water Supply
Ganquan borehole pumps lift groundwater from wells for agricultural irrigation and water supply. Installed below the water level, these submersible pumps deliver water to surface storage or distribution systems. Selection depends on the required flow, total head, borehole diameter and water conditions.
Tell us about your well and the water supply you need. We can help review suitable options and confirm the pump, motor and supporting equipment for your project.

Built to your well, not pulled off a shelf. Tell us the borehole diameter, the water you need and the power you have — we match the pump, motor, cable and control panel to your actual conditions.
Typical Applications
Groundwater Extraction
Lift groundwater from boreholes to surface storage tanks or collection systems.
Agricultural Irrigation
Supply well water for farmland irrigation, with pump selection matched to the required flow and irrigation pressure.
Water Supply
Transfer borehole water to storage and distribution systems for communities, facilities and other water supply projects.
QJ & QJT Borehole Pumps
The QJ and QJT series cover a range of borehole pumping duties for groundwater extraction, irrigation and water supply. The appropriate model, number of stages and motor configuration depend on the required flow, total head, borehole dimensions and operating conditions.
| Parameter | Catalogue Range |
|---|---|
| Flow rate | 20–600 m³/h |
| Head | 6–600 m |
| Borehole diameter | 150–400 mm |
| Motor power | 3–250 kW |
These figures describe the overall catalogue range across different models. Maximum flow and maximum head do not apply simultaneously to a single pump. Final selection requires the performance curve and installation requirements of the proposed model.
Range at a Glance by Well Size
| Well casing | Series | Flow (m³/h) | Head (m) |
|---|---|---|---|
| 150 mm (6″) | 150QJT | 5–32 | 18–450 |
| 175 mm (7″) | 175QJ / 175QJT | 20–70 | 24–330 |
| 200 mm (8″) | 200QJ / 200QJT | 20–100 | 12–420 |
| 250 mm (10″) | 250QJ / 250QJT | 50–160 | 15–600 |
| 300 mm (12″) | 300QJ / 300QJT | 200–350 | 20–270 |
| 350 mm (14″) | 350QJT | 400–600 | 17–119 |
Ranges cover different models and stages. Maximum flow and maximum head do not occur simultaneously on a single pump.
Motors 3–250 kW across the range. Standard: 380 V ±5%, 50 Hz, 3-phase. Custom builds: 60 Hz, 220 V, 660 V. Model-by-model tables (555 models) — ask our engineers or use the Online Pump Selector.
Note: the ranges above describe the historical catalogue. Current factory supply starts from 20 m³/h (175QJT20 and above); smaller-flow requirements are reviewed case by case. Exact model, head and diameter combinations are confirmed per order.
Operating Conditions
The catalogue lists the following standard operating conditions for the QJ/QJT range. Suitability must be confirmed for the selected model and the actual well water.
| Parameter | Standard Catalogue Condition |
|---|---|
| Water temperature | Up to 20°C |
| pH value | 6.5–8.5 |
| Solids content | No more than 0.01% by mass |
For warmer water, sandy wells or corrosive water, contact us before selecting a pump. Share any available water analysis or well test report so we can review the appropriate pump series and materials.
QJ Borehole Pump Certification
Ganquan’s QJ series is covered by China water-saving product certification for the models and specifications listed in the certificate.
| Item | Certificate Details |
|---|---|
| Certified series | QJ |
| Applicable well diameter | 150–400 mm |
| Motor power | 3–315 kW |
| Product standard | GB/T 2816-2014 |
| Certificate No. | ZSRK-JS1660-001-2025 |
| Certificate validity | 3 January 2025 – 2 January 2028 |

Explore our quality inspection and pump testing facilities.
Manufactured by Ganquan, Supported by Our Overseas Sales Team
Ganquan Pump designs and builds its pumps in Tianjin, China — 10 borehole pump series covering wells from 150 mm, with motors, cables and control panels supplied as one matched package. Importers and distributors work directly with our export team: OEM branding, custom voltage and frequency options (60 Hz, 220 V, 660 V), and factory lead times. Our QJ series holds the Chinese water-saving product certification (GB/T 2816-2014), and our quality system is ISO 9001 certified.
How your RFQ moves
- Send your well details
- We select a candidate model from our catalogue tables (QJ/QJT series, 10 series covering 150–400 mm wells)
- You receive a written quotation with model, parameters and lead time
- Production at our Tianjin facility
- Every pump is tested on our in-house test rig — checked against its rated parameters, for leaks and for reliable operation
- Shipment with packing list and documents
You know which step your order is at — no silent weeks.


Before you compare quotes, check these five lines
- Exact model and stage count — e.g. 250QJ80-80/4 means: 250 mm well, 80 m³/h, 80 m head, 4 stages. No model number, no real comparison.
- Voltage and frequency matched to your grid — not just “3-phase”.
- Cable and control panel — cross-section and protections (short-circuit, phase-loss, overload) listed or not.
- Water condition limits confirmed for your well — chloride, temperature, sand content.
- Lead time and packing in writing.
A cheaper quote that skips these lines usually costs more later.
Frequently Asked Questions
What information do you need to select and quote a borehole pump?
Three numbers: required flow (m³/h), total head (m), and well casing diameter (mm). Tell us your voltage and frequency too — we build 380 V / 50 Hz 3-phase as standard and 60 Hz / 220 V / 660 V on request. Our engineers check your numbers against the model tables and reply with candidate models.
Can you build pumps for 60 Hz grids?
Yes. 60 Hz, 220 V and 660 V are listed customization options. Note that 220 V refers to voltage, not necessarily single-phase supply — single-phase requirements are confirmed case by case with our engineers.
What is the head range of your borehole pumps?
6–600 m across the range, depending on series and stages. How deep a pump can be installed in your well is a different question — it depends on your static and dynamic water levels, plus the unit length of the selected model. Send us your well data and our engineers will work it out.
Do you supply control panels and spare parts?
Yes — cables, control panels and spares can ship as one matched package with the pump. Protection functions (including dry-run protection options) are configured per order; confirm the exact combination with our engineers.
Can the pump run on solar power?
We do not offer a standard solar-direct package. The usual setup is grid or diesel-generator power with reduced-voltage, soft or VFD starting. If solar is essential for your project, contact us to review options.
Further Reading
- How to Choose a Borehole Pump: 5 Parameters You Must Know
- Well Depth Is Not Pump Head: How to Calculate TDH
- Borehole Pump Prices: What Drives the Cost (and How to Get a Factory Quote)
- Buying Borehole Pumps from China: An Importer’s Factory Evaluation Checklist
- Single Phase vs Three Phase Borehole Pumps: How to Choose
- Borehole Pump Troubleshooting: 7 Symptoms, Causes & Fixes
- Borehole Pump Maintenance Schedule
- Borehole Pumps for Farm Irrigation
- Community Water Supply Buyer’s Checklist
- How Our Overseas Sales Team Supports Your Project
Tell Us About Your Well
You do not need every technical detail to start an inquiry. Tell us where the project is located, what the water will be used for and what you already know. The following information helps us review suitable pump options:
- Well details: borehole internal diameter, total depth, water level during pumping and any available well yield test.
- Water demand: required flow rate, or the amount of water needed each day and planned pumping hours.
- Delivery route: where the water needs to go, elevation difference, pipe length and diameter, and any required outlet pressure.
- Power supply: available voltage, frequency and single-phase or three-phase supply.
- Water conditions: temperature, sand content and any available water analysis.
- Existing equipment: photographs of the current pump and its nameplate, if this is a replacement.
Well depth alone does not determine the required pump head. If you are unsure about a value, leave it unknown and share any available photos or reports. We will help identify what still needs to be checked.
Request a Borehole Pump Quote
No complete specification is required. Tell us what you know — your required flow, head, borehole diameter, country and power supply — and we will help you select the pump.
